BMW Z3 coupe Manuel d'utilisateur télécharger pdf

ProjectorZ™

Installation Instructions

BMW Z3/Coupe and ///M Roadster/Coupe

1 of 8

Thank you for purchasing the ProjectorZ™ Projector Lighting System for your BMW. These instructions

will walk you through the few steps required to install the system. Note that this system is compatible

with all versions of the Z3, Z3 Coupe and ///M Roadster or ///M Coupe, regardless of model year or

headlight variation.

1.0 Required Tools

Normal Installation

• Needle nose pliers

• A #10 Torx driver (screwdriver or socket type)

• A medium flat blade screwdriver

• An 8mm nut driver or socket and ratchet

• Optional pencil magnet to retrieve and insert mounting screws

• A 19mm Open End Wrench (recommended)

• A 17mm and 10mm socket and ratchet

• Use of a normal kitchen oven

• A cookie sheet (Disposable or regular)

• 2 oven mitts

• 1 2.8 oz. tube of 100% silicone glue (black or clear)

2.0 Installation Notes and Warranty

Please read completely through the instructions before beginning.

The kit is very easy to install. But you must take your time. It is suggested that you wear eye protection

when installing the system if your product is fitted with the optional DDE Lightning Plus™ rings. All

fluorescent lamps contain small amounts of the element Mercury. If you break a ring do not blow the

debris away or inhale the powder. Wipe up any debris with a damp paper towel and dispose of it. Handle

the rings with care until they are installed inside of the bezel of the headlights and they will provide years

of trouble free operation. Lamps can last for over 100,000 hours of operation.

This procedure assumes that you are familiar with your headlight wiring method. If not, please refer to

your dealer for assistance as required.

Apexcone.com warrants the normal operation of this system for life. Return any non-performing

component for immediate replacement.

Enjoy your product and thank you for your purchase.

1 2 3 4 5 6 7 8

Résumé du contenu

Page 1 - 1.0 Required Tools

ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Roadster/Coupe 1 of 8 Thank you for purchasing the ProjectorZ™ Projector Lighting Syst

Page 2 - 3.0 Kit Contents

ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Roadster/Coupe 2 of 8 3.0 Kit Contents Each system contains different contents based

Page 3 - 4.0 Installation Procedure

ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Roadster/Coupe 3 of 8 4.0 Installation Procedure Remove the 4, 8mm screws securing y

Page 4

ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Roadster/Coupe 4 of 8 Set your kitchen oven to pre-heat to 200 degrees and locate a co

Page 5

ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Roadster/Coupe 5 of 8 Once you have the lenses out, fit the new bezels into the old op

Page 6

ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Roadster/Coupe 6 of 8 Using a #10 Torx driver, remove the screws holding the 2 white n

Page 7

ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Roadster/Coupe 7 of 8 The new mounting brackets are now ready to install into the head

Page 8

ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Roadster/Coupe 8 of 8 Next, Connect the new H9’s with the plug and play harnesses that

Commentaires sur ces manuels

Pas de commentaire

BMW Z3 coupe Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Électronique des véhicules automobiles BMW Z3 coupe. ProjectorZ™ Installation Instructions BMW Z3/Coupe and ///M Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Électronique des véhicules automobiles BMW Z3 coupe