BMW K25 R1200GS - Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Kits de voiture BMW K25 R1200GS -. 77 51 001 Installing LED auxiliary headlights Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 12
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
77 51 001 Installing LED auxiliary headlights (14 FRUs)
+
77 51 502
Equipment trim-level variant:
LED auxiliary headlights
Note
Not all the components contained in the installation kit are necessary for
installing the auxiliary headlights.
Note
Conversion/retrofit also work without registration with the BMW Motorrad
diagnostic system. Registration is advisable, however, so that they will
subsequently be detected by the system whenever work is carried out with
the diagnostic unit.
Note
The LED auxiliary headlights have an overheat cutout. The headlights
automatically reduce their brightness if a certain temperature is reached;
under extreme circumstances the headlights can even switch themselves off.
The headlights return to full brightness once they have cooled down
sufficiently.
Preparatory work
Removing front and rear seats
Removing left side cover
Removing left side panel
Remove the right side cover
Removing right side panel
Removing trim panels of fuel tank
Removing intake air pipe
Removing fuel tank
Core activity
(-) Preassembling brackets for both sides
Seat nut (1) in bracket (2).
Insert LED auxiliary headlight (3) into bracket (2).
Tighten screws (4) just tight enough to hold the LED auxiliary headlight in
position, so that beam throw can subsequently be adjusted.
BMW-Motorrad - 0450 - R 1200 GS, K25 31
1/12
122012
Vue de la page 0
1 2 3 4 5 6 ... 11 12

Résumé du contenu

Page 1 - LED auxiliary headlights

77 51 001 Installing LED auxiliary headlights (14 FRUs)+77 51 502Equipment trim-level variant:LED auxiliary headlightsNoteNot all the components conta

Page 2

Place fairing bracket (6) in position (arrow).Install screw (5).Tightening torquesFuel tank with bracket to front frameM8 x 45 - 10.919 NmCheck the O-

Page 3 - (-) Releasing control unit

See the information about the BMW Motorrad diagnostic system for allfurther instructions.Connect the BMW Motorrad battery charger.Workshop equipmentBM

Page 4 - (-) Securing control unit

Disconnect KOMET from the motorcycle and screw the cap onto thediagnosis plug.Disconnect the BMW Motorrad battery charger from the motorcycle.Finishin

Page 5

(-) Installing brackets with LED auxiliary headlights on bothsidesRemove screws (1); these screws are no longer needed as longer screwswill be install

Page 6 - (-) Routing wiring harness

Continue routing actuating cable (1) down.(-) Releasing control unitOpen the clips (arrows) and swing up cover (1) and secure it so that itcannot clos

Page 7 - (-) Securing cable

(-) Securing control unitInstall control unit (2).Lower cover (1) and engage the clips (arrows).(-) Installing wiring-harness adapter kit for LED auxi

Page 8

The cable colours of the LED wiring-harness adapter kit do not match theoriginal colours of the auxiliary-headlight cables.Always connect brown to bro

Page 9 - (-) Installing fuel tank

(-) Routing wiring harnessSeat retainer (1) on cable duct (2).Technical dataFuse for auxiliaryheadlight7.5 ARoute cable (3) forward along wiring harne

Page 10

(-) Securing cableSecure cable with cable tie (1).If the cables are too long use a cable tie (arrow) to secure the looped cableto wiring harness (2).(

Page 11 - Precondition

(-) Wiring-harness routing for right LED auxiliary headlightRoute cable (1) along fairing carrier (2) toward the right LED auxiliaryheadlight and secu

Page 12 - Finishing work

(-) Installing fuel tankPush the fuel tank from behind into the rubber mounts on the frame. Makesure that no lines, hoses or Bowden cables are trapped

Commentaires sur ces manuels

Pas de commentaire